Hook up above ground pool filter

What You Need to Open Your Above Ground Pool

Print Guide. See All Steps. Step by Step. Step 1 Before starting installation, you will need to purchase sand. Use only high rate No. An example is pictured at left. Check the manufacturer to determine the amount required. This unit Hayward ST uses 3 50 lb bags of sand - lbs total. You can also purchase our superior to sand Click here for our Sand Alternative. Step 2 When installing the pool sand filter, you will connect it right after the pump.

Life Hacks for Your Smartphone

Pool water will come in through the pool pump, be filtered through the sand filter and released to the chlorinator before returning back to the pool. If you have a pool heater, the pool filter will release water to the heater before going to the chlorinator. Step 3 The pool filter should be installed on a level concrete slab not more than 6 feet above the pool water level.


  • indian girl dating sites.
  • Disclaimer;
  • How to hook up a sand filter pump to an above ground swimming.
  • Best Above Ground Pool Pumps 12222 – Buyer’s Guide.
  • free gothic dating sites.
  • online dating country singles;

Position the pool sand filter so that the piping connections, multiport valve and drain are convenient and accessible for operation and maintenance. Place the filter next to pump. Step 4 Before you connect the pool sand filter into the piping system, you have to assemble the filter. If the threads aren't prepared, wrap them with two layers of Teflon tape. Start in a clockwise direction at the first thread with a half width overlap for the full length of the thread.


  • 1. Clear Your Winter Pool Cover.
  • bonjour matchmaking denver.
  • Connecting the skimmer:?
  • Don't Compromise..
  • Filter Parts for Above Ground Pool.

Be careful when screwing the gauge on. Use a wrench on the square nut on the final turns. Step 5 Make sure drain cap is securely in place. This will help protect the laterals. Step 7 Next you will be installing pipe and lateral assembly inside the tank. Separate the valve from the pipe and lateral assembly. Also make sure the 10 laterals at the end of the pipe are rotated up. They have to be in their up position to fit through the hole in the top of the tank. These laterals are somewhat fragile. Ensure that none are cracked or broken.

Guide to Setting Up Your Above-Ground Pool Equipment - The House Designers

Place the pipe and lateral assembly inside the tank. Step 8 After the lateral assembly is inside, carefully rotate the 10 laterals 90 degrees in their down position. Step 9 Make use the pipe is centered in the opening. Tape the top of the pipe to prevent sand from entering and clogging the laterals. Step 10 The sand filter package comes with a cardboard sand shield. Place this over the pipe and within the opening.

Step 11 Pour sand carefully into the pool sand filter until laterals are fully covered. For this unit 3 bags should leave at least 6" space between the top of the sand and the top of the filter. Level sand as you pour and make sure the center pipe remains centered in the opening. Be careful when leveling the sand that you do not lift the pipe and lateral assemble up off the bottom of the tank. You will not be able to push the pipe back down without causing the laterals to rotate up.

Step 13 Remove tape from top of pipe. Slip the Multiport control valve onto the central pipe - check the O-ring to ensure it is positioned correctly. Step 14 Install clamp around the tank and valve flange. Loosely tighten clamp so that the valve can be rotated on the tank for final positioning.

Step 15 The next step is to connect the "PUMP" port of the multiport valve to discharge side of pump. You will need to screw a straight thread adapter purchased at a hardware store into the "PUMP" port. To help seal this connection wrap two layers of Teflon tape the adapters.

Do not over tighten or you cause the joint to fail. Step 17 Cut a short piece of pipe and glue it to the adapter. Make sure the pipe and inside of the adapter are clean. Gluing is a two-step process. First apply a thin but even coat of purple primer on each surface to be joined: the outside of the pipe and the inside of the adapter.

After the primer dries, apply a thin even coat of glue to both surfaces. Wait 30 seconds for the glue to set.

Step 18 Glue on a union to facilitate future maintenance on the pool sand filter or pump. In years you will have to disconnect the multiport valve from the tank to change the filter sand.

How to Hook Up a Sand Filter Pump to an Above Ground Swimming Pool

A union will save you from having to cut it out of the piping. Step 19 Screw another adapter into the discharge side of the pump then add piping and elbows required to connect the filter and pump ports. In a basic system this connection will probably be to the Chlorinator. Also add a union to this line for future maintenance. Note: This picture does not show the water hose. Step 22 Tighten multiport valve flange clamp with a screwdriver.

Tap around the clamp with the screwdriver handle as you are tightening the clamp to help seat the clamp properly. Place vinyl protector caps over the ends of the screws. Step 23 Your new pool sand filter should now be ready to operate. Make sure that your waste line is rolled out to where you want to dump the pool waste water.

Step 25 Prime and turn ON the pool pump.

Write a Review (1000 Gph Krystal Clear Cartridge Filter Pump, 110-120V with GFCI)

Be sure that you have at least one suction and all discharge lines open. Step 26 Run the pool pump for 2 minutes after you have a steady flow of water out the waste line after the pump is fully primed. This will flush all the impurities or fine sand particles out of the sand media. Based on 1 review. Filter pump works great! Runs strong and setup was quick and easy. Availability: In Stock.

Life Hacks for Your Smartphone

Rating Required Select Rating 5 stars best 4 stars 3 stars average 2 stars 1 star worst. Review Subject Required. Comments Required.

Start Up Instructions for your New Above Ground Pool

Benefits include: Improved circulation and filtration Improved water clarity Increased negative ions at the water surface Suitable for Intex pools up to 6, gal with 1. Write Review. Intex Recreation Corp. While all accidents cannot be prevented, practicing good safety habits, setting and following rules, carefully reading instruction manuals, and vigilant supervision can greatly reduce the likelihood of injury as well as reduce injury severity. Please take the time to review the following information, and make use of the link provided, to assist in keeping you and your family safe from injury.

admin